❤️[7 Easy Steps] How To Cut Foam Mattress?

When it comes to How To Cut Foam Mattress? you need to be careful not to make any cuts that would compromise the integrity of the product. The first step in this process is to measure and mark where you want your cut to take place.

This will ensure that there are no mistakes when you start making your cuts. Once you have marked the area for cutting, use a sharp knife or razor blade and carefully slice along those marks until you have completely separated the two pieces of foam from one another.

Grip the knife firmly in one hand and insert the blade remover’s edge into the rounded or square head of the razor, pulling gently to release it from its locked position.

Slide the razor under an edge of foam mattress, pulling very gently to remove it from its connection with other pieces of foam. Once loosened, slice through the material either lengthwise or crosswise until you have cut off enough strips for your needs. You can then take off any remaining bits by cutting close to any adjacent pieces.

How To Cut Foam Mattress?

For Cutting a Foam Mattress we need some Equipment that is listed below:

1. Measuring tape

The measuring tape is a short length of spring steel, flat on one side and heavily ruled on the other. It also has some form of the locking mechanism to ensure it stays in place.

A measuring tape can be used to measure at close quarters things that are difficult to measure with the use of a ruler.

The measuring tape can also be used to make a straight cut along a surface. What’s more, the use of two measuring tapes tethered together by a piece of the string allows you to transfer measurements from one point or surface to another.

This is useful when transferring measurements from an existing object/surface onto something else (such as cutting foam mattress).

More: How To Cut A Futon Mattress In Half

2. A sharp razor/knife

To make your work easier you can use an electric cutting knife. Its blades are very sharp, it doesn’t take much effort to cut, and the task will be completed in less time.

An electric cutting knife is also good for Cutting Foam mattresses by Professionals. Marker A Ruler or tape measure with inches shown Measure the mattress that you want to trim down to see how many inches you need to remove. 

You must mark this area on both pieces of foam so you can accurately match up your new pieces when putting them back together again later.

When you have marked out the areas on each side of where your cut needs to go, put your hand firmly on top of

3. Marker

A marker (or “sharpie”) is a permanent ink pen used to make dark marks on objects. The ink is often made of low-to-medium grade oil and the ‘writing end’ consists of a hard, fine tip similar to that of an indelible marker.

Marker can be useful for marking out areas (or outlines) where you need to cut your foam mattress down to size.

4. Seam ripper

We need a seam ripper in case the mattress cover is not removable. This tool is used to remove stitches in fabrics.

A seam ripper begins like a sharp, triangular point attached to a thin, oblong handle.

The thin, pointed end of the blade (the actual cutting part) has two tapered sides that form an inverted V shape. The cutting area(s) can be anywhere from 1-2 inches long.

The seam ripper is useful for removing old stitches while still maintaining some of the mattress foam material underneath its new stitches.

Sharp Scissors Sharp Scissors are similar to ordinary scissors, but with sharp points at their tips instead of blunt ones. This allows you to make more precise cuts than you can do with regular scissors.

5. Sewing Kit

A sewing kit is an assortment of different types of thread, needles, and other items used in the practice of mending clothing or other textiles. Different types of material require different types of thread to be sewn together.

The use of a sewing kit helps people sew things back properly (e.g. sewing foam pieces back together) upholstery needle A special type of long needle that has a wide eye for passing thick thread through its slender shaft.

Suitable for making mattress seams stronger if needed.

Table/Chair Table/chair is an essential workstation for most DIY projects involving cutting (and trimming down) foam mattresses as well as stapling fabric onto a mattress cover.

6. Piece of Plywood/Hardboard

A piece of plywood/hardboard is a thick flat section manufactured from wood veneer. The core material can be softwood, hardwood, man-made material, or a combination of these materials.

If you don’t have a suitable surface to work on, you should place your foam mattress on top of a piece of plywood/hardboard to prevent it from being punctured.

Scissors are small hand tools that consist of two blades attached at one end by a hinge pin. You simply hold the handles and open or close the blades against each other using your thumb and fingers to cut something (e.g., foam mattress) into two pieces. 

Steps For How To Cut Foam Mattress?

For Cutting a Foam Mattress we need to follow some steps that are listed below:

1. Take your mattress cover off

Take your mattress cover off to access the foam. Some mattress covers are removable while others are not. Even if it is removable, some people may have chosen not to remove it to protect their mattress from being stained or altered during the cutting process.

2. Lay the foam mattress flat

Place your mattress on top of a piece of plywood or hardboard to prevent it from being punctured during the cutting process. Make sure that you’ve taken out any bedding already. This will also help if you are trying to remove some sort of removable cover, instead of looking for seams only where the mattress fabric meets the foam.

3. Determine the size and dimensions

Determine the size and dimensions of your mattress. Decide how much foam is required to fill in the area you need.

For example, if you are replacing an old spring mattress with a new memory foam one, your new, smaller memory foam mattress will likely be about five inches narrower and shorter than the original spring unit.

Use this information to determine the amount of material needed before cutting anything. Note that many mattresses have indentations on both sides where people usually sleep.

If your replacement mattress includes these impressions, you will not want to cover them up. This means either taking away more from the top or side or just leaving it with no added thickness at all.

4. Measure and mark where you want to cut

Use a tape measure to measure your mattress and mark the measurements on the foam with a marker or pen.

Once you have done this, move your hand around slowly feeling for any protrusions. Often if there is an indentation in the middle of the mattress, there might be another one made by its frame which could catch something sharp.

Double-check that everything is correct before making the first cut. If you are not sure whether your measurements are correct, make some sort of temporary fix to hold it all together (e.g., duct tape) before cutting anything to ensure you can always recover if needed.

Cutting mat is used as protection when using knives or other cutting tools either workpieces or blades.

5. Cut the mattress without compressing the foam

Take a sharp blade and cut along your marked lines without trying to “compress” the foam. If you put pressure on the knife, you can accidentally cut all the way through. Therefore, just gently saw back and forth until you get the desired results.

You can use a loaf of bread or a serrated knife if you don’t have one of these special cutting tools available.

Cutting mat is used as protection when using knives or other cutting tools either workpieces or blades.

6. Finishing up

Once your mattress is cut to the right size, you need to decide whether you want to add thickness and then:

If you did not remove your cover and it has a zipper, open it and take out any bedding. Make sure that the replacement foam fits inside completely.

Remove any old padding from the cover by cutting along its seams, usually found on one of the longer sides.

Then stuff in the new padding until it meets the edge of where you opened up. Use a marker or pen to mark where it should cut before removing this extra material without cutting anything yet.

7. Cover your mattress with fabric

Lay your fabric face down on a flat surface and place the foam in the middle.

Then fold the two sides over so that they overlap about 4 to 6 inches. Make sure there is enough fabric at this point so you can later use safety pins or duct tape to keep them together.

Next, flip it all back over and do up the zipper (if necessary). It should look like a rectangle at this point which you would normally place under your fitted sheet.

Use safety pins or duct tape depending on what you have available to attach both of the short ends through the mattress cover. Then insert your new mattress into its bedding.

Mattress covers Mattress covers are designed to protect mattresses from dust mites and stains.

Conclusion For How To Cut Foam Mattress?

The best way for How To Cut Foam Mattress? is by using an electric knife or wire cutter. You can also use scissors but it will take more time and effort. To protect the fabric, place some cardboard on top of the cutting surface before you start slicing through your mattress with either tool.

This should reduce any damage that could be done to your sheets or other materials used for bedding purposes. Be sure not to try this if you have memory foam because these are too difficult to slice without making them unusable afterward!

When you are finished cutting the foam mattress, make sure to use a vacuum cleaner with an upholstery attachment or brush attachment to remove any excess dust.

You can also cover the cut section of the mattress with plastic wrap before putting it back in its original packaging for storage until ready for installation. We hope this article has helped you learn how to cut your own foam mattress!

Leave a Comment